Відео

I wonder if it’s the same for older model dodge vans?

I called the air conditioning company and complained about the weak air coming out of the indoor unit. When they examined it, they found that the fan was dirty, so they used compressed air to remove the dirt from the fan. I noticed that they also blew from the top of the air conditioner fins from the top in order to get the dirt inside the coils out for cleaning.

That mfer is hard on 2003 monte carlo

Thankyou none of stud finders worked reliably

Love this. The hose and clamp idea is genius!

Do u think this kaboat is sea worthy or the heavy duty version

how about compressed air?

OK, everybody keeps showing me stuff but I’m not actually seeing it being done

Oil base will be dull. Water base will shine, but water base will peal over time in the sun. Oil base is the way to go.

Hi - I loved your video on the BRIS inflatable kayak. I’m trying to decide between the Saturn Heavy-Duty KaBoat and a Bris. I am interested in how these two brands compare in your experience. Thanks in advance for your help!

Is it the same for a 1999 Buick century do you know?

Did you put the tung oil on over ready seal

Would you use only Hope's Tung oil instead of Ready seal? I want to protect my gate and fence. Please reply. Thank you for your attetion to this matter. Raul

Straight to the point instructions well done sir 👍🏽

What was the put-in/take out? Love the dude that just pulled out the poison ivy. But you are so right, go wash the oil off and you’ll be good to go.

John…you can do anything solo!!! Great idea!!!

I wonder if using a mister would make less of a mess and you could just leave it on all the time. I'll find out tomorrow for you! Also, you mentioned making pencil marks for cuts, I just use a permanent marker on the bottom of the paver, worth a try!

Great video. Thanks

Very useful review. Thanks for making the video!

I was told to use Bee wax in between the pieces of slate to make it smooth. The reason you use Bee wax is there are no petroleum products in the Bee wax so there would never be a mark on your felt later down the road... Works great...

Well, apparently, you really didn’t look at your rack because you got three balls in a row all solids and three times around your rack your hair you have two balls that are in line with each other so you need to look at your rack again it sucks sorry

You handled it well.

Why do people get so upset the way its right.high and low balls on the end

Well done. I think Jim should have pulled harder

How did you get the pipe in with the coupling on?

Thankyou Thankyou Thankyou!😊

THANK U, had someone try and say it goes in numerical order 😂

3800 and 3400 engines are in different places.

Your way is not what I see when watching eight ball tournaments I’ve taken photos during a Reyes match

Thanks for this video it really helped me, my 1987 G10 is similar but only 2 bolts hold it on; unfortunately, the top bolt was gone. I notice a grinding noise when it was running. I am going to go get it tested now.

Would removing that heater hose help any?

Can I use a regular magnet

exactly same situation, I know where studs are but you want to be sure, didnt think of simple magnets, thanx again, since stud sensor cannot read through tile

thankyou

I like that rusty van!

Your's must be a 3.8. Replaced thermostat in my daughter's '05 Impala 3.4 today it was down under air intake. Very different job. Wish it was as easy as your 3.8.

Not sure why this was randomly recommended to me lol. This was very informative, however I will say that by the time most people get to something as tedious as actually replacing an entire drain pump, they likely have already checked their filter before hand. If you're craft enough to take apart the entire front panel of a washer machine, you already have checked your filter. Good info though regardless!

Thankyou! It helped!

Great instruction and video, there is usually a rhyme or reason to many things and in this world, using stuff eventually there need to be maintenance, just so many other things to look after, liked your reasoning on the pump, my LG is well over 5yrs and I have never did anything maintenance wise, now standing water, got to do something, thanks for your video 😊👌🏽👍🏽,got to get busy, will evaluate pump for restricted flow!

Thank you for your video, can I ask what size the engine is, wondering if yours is a 305, thanks

Thanks. Why can’t you just flip the washer on its side and access the pump from the bottom instead of going to all the trouble of removing the front housing?

13ths?

Great job, review and best part showing how to assemble solo.

I am going to give it a shot

ty sir

this help me a lot 👍🏻 thanks

Had an ice cold bud light and think I’ll follow your advice and buy this cooler.

Guess they never did a stick check?

Thank you so much. Perfect directions! And so easy.

Thank you for this. I am currently doing the exact same thing. And i am very cautious about it being good enough before laying the cloth down.